How to fix the rear cable on the Elise S2 long roof soft top

From TechWiki
(Redirected from TechWiki:S2)
Jump to navigation Jump to search

1) Short description of the long roof top

There are 2 cables in the soft top : front and rear.

Pic01.jpg
Pic02.jpg

Both cables are quite the same but the few differences aren’t negligible.

1.1) Similarities

Each cable have the same technology :

  • a fastening plate where the cable is set (left side)
  • a cable (awesome, isn’t it ?)
  • an hollow nut. And inside the nut we can notice the other setting of the cable
  • a fastening plate with a threaded part

1.2) Differences

  • The rear cable is a few centimers longer than the front cable.
  • The rear cable is the only one with a cover.
  • The fastening plates of the front cable are srewed in the roof trim panels. So it’s easy to change.
  • The fastening plates of the rear cable are set in plastic parts. And that’s why it’s not easy to change. ^_^

2) What we are going to do

Trying to fix the rear brocken cable and finnally getting both new cable !

At the start : used front cable, brocken rear cable

3) Needed stuffs

Pic04.jpg

External things :

  • a bowden bicycle braking cable with :
    • an inner cable
    • a housing cable
  • 1 pop rivet with a diameter of 4 mm
  • 2 pop rivets with a diameter of 2mm
  • the official front roof cable (REF : B116V0064H)

NB : in real life, I suggest to have a few pop rivets more in case of one of the following steps goes wrong...

Tools :

  • Drill with a 3,5mm bit
  • Dremel
  • Cutting plier
  • Hand metal saw
  • Pop rivet plier
  • Vice
  • Measuring tape
  • Hammer

4) Let’s go !

Step 1 : Changing the front cable

All right, that’s strange to change the front cable in order to fix the rear cable. But as we’re going cut and recycle parts, it’s more efficient to cut the old cable instaed of the brand new one.

Just follow these this simple article "Fixing a broken roof cable" : [1]

Pic05.jpg Pic06.jpg

Step 1 finished : new front cable, rear cable still brocken

Step 2 : Unmount the rear cable

Unscrew the hollow nut, take off the cable and keep the cable for further steps.

Pic08.jpg
Step 2 finished : new front cable, nomore rear cable

Step 3 : Remove one of the old fastening plate

Pic10.jpg

You have to keep the fastening plate with a threaded part and take off the other.

  • Remove a few material to see the fastening plate
  • Drill carefully to split the plastique support and the fasting plate without touching the material.

Step 4 : Prepare the pop rivet for setting

To set the «new» fastening plate we’ll use the 4mm pop rivet. But as it’s a bite too long we have to work on it a little. Pic11.jpg

Step 5 : Setting the plate

Here we start recycling : take the fasting plate with a threaded part from the old front cable and set it on the plastic part with the 4mm «shorted» pop rivet.

Pic12.jpg Pic13.jpg

In order to finish it cleanly you can use a Dremel to get a smooth area on pop rivet and then paste back the pieces of material that you remove at the step 3.

Step 5 finished : new front cable, nomore rear cable but 2 fastening plates WITH threaded part

Step 6 : Still recycling

We have threaded parts on both side so we need 2 hollow nuts now. We can find them on the old front cable and the old rear cable.

For each cable :

Pic15.jpg

Step 7 : Let’s decapitate !

Here again we’ll modify some pop rivets : just decapitate at least two 2mm pop rivets.

Pic16.jpg

Step 8 : Making the new rear cable

Just follow keep it in the right order :

  • Cut the bicycle braking inner cable to get a piece of about 1 meter long
  • Cut the bicycle braking housing cable to get a piece of about 0.95 meter long
  • With one of the 2 unheaded body rivet, set the left side of the inner cable in a vice
  • Put on from the right a hollow nut (from step 6) and take time to check if the setting take place inside

the hollow nut. If not, file down a little the setting.

  • Put on the housing cable from the right
  • Put on the second hollow nut from the right
  • Set the right end like you did for the left. And check again if the setting take place correctly inside the

hollow nut.

Step 8 finished : new rear cable

Step 9 : Final assembly

Just put your new cable at the correct place.

Step 9 finished : Job done !!

What you get in the end

Both cables changed and an rear cable easy to fix in the futur.

Pic19.jpg