Petrol Cap

From TechWiki
Jump to: navigation, search
S1 Elise. part.10501

The internals of the Elise S1 petrol cap are manufactured by Stant. It's also used by Jeep, from whom you're more likely to be able to readily obtain it.

On-line sources include Rock Auto in America. The part number that you need to order is 10501, delivery should be expected in about 1 week. You may also be able to get it from a UK Jeep dealer - please add your sources here if successful.

I started from the point of having had the filler cap disintegrate on me, so almost all the parts had come out of the cap.

Fuel cap 1.jpg

All that was left inside were the plastic ratchet (1), metal collar (2) and black plastic retainer (3)

Fuel cap 2.jpg


Using a screw driver, prize the bottom part of the plastic ratchet out from behind the metal collar

Fuel cap 3.jpg

The top part of the ratchet will now come out freely from behind the metal collar.

Fuel cap 4.jpg

Be very careful not to damage the black plastic retainer. You need this to fit the new components.

Take the new filler cap and use a Stanley knife to cut tabs into the side of the filler cap.

Fuel cap 5.jpg

Be careful not to cut into the white plastic components covered by the cap. Gradually cut away the cap, until most of the white plastic components (but not the barrel lock) and the metal collar are free from the cap. Once you’re able, remove the white plastic components and the metal collar from what’s left of the filler cap.

Carefully cut around the lock barrel, again making sure that you don’t damage the white plastic

Fuel cap 6.jpg


Remove the barrel and push it into the hole in the old filler cap. The barrel has a key-way and locking tabs which keep it in place

Fuel cap 7.jpg

– make sure you’re putting it in the right way. Note the location of the spring pin

Push a screwdriver down the side of the old metal collar, lever it out of shape and remove it from the old cap. Again, take care not to damage the black plastic retainer.

Fuel cap 8.jpg

Fuel cap 9.jpg

Take the lock mechanism from the new cap and place it on top of the lock barrel

Fuel cap 10.jpg

. Note that the long tongue goes into the deeper recess in the cap. This is on the opposite side of the lock barrel from the spring pin.

Put the two parts of the ratchet mechanism into the old cap, making sure the one with the row of teeth is nearest the top of the cap and the other part of the ratchet is towards the “fuel tank”. Put the threaded stopper onto the top of the lock mechanism.

Fuel cap 11.jpg

Take the metal collar from the new cap.

Fuel cap 12.jpg

With the channel in the collar facing you, put it into the cap and using a flat screwdriver, gently push it past the lugs on the black plastic retainer.

Grip the threaded stopper in your hand and check that the lock and ratchet operate normally. Use a silicone lubricant (not WD40) on the ratchet and in the key hole. Job done.

As a final safety measure, I'd recommend not fitting the cap until you've filled the car up at a petrol station near home and have time to come back and remove the cap if it fails. Don't forget to change the fuel filler keys on your key ring as well.

All pictures exept Stant cap+keys copyright (C) John Fletcher 2008

If you don't want/can't obtain a stant cap.. My basic research (clicking around the stant and rock auto websites until boredom made me stop) listed these cars as having the same filler cap as the S1...

2001 Jeep Wrangler 2002 Dodge Viper 2002 Kia Rio 1998 Volvo S90 1998 Volvo C70 1994-1998 Jeep Grand Cherokee 1995-1997 Land rover discovery

A plastic replacement from UK ebay based on this list was not close enough to follow the procedure above, but did fit the neck properly on the car - after unclipping the tip of the cap which exended to far down the neck. This is an easy way to obtain a lightweight cap for about £10.

Alternative technique

My filler cap didn't fall apart but when I unlocked it it the cap still spun, not gripping on the inner part of the cap. I managed to remove it by using a pair of pliers on the key to undo the cap (phew).

I bought a Stant cap from the USA (£14 in 2014) and removed/destroyed/shredded the black cover using pliers and side cutters, ensuring I didn't damage the white mechanism, the metal retaining ring.

Its worth remembering that the lotus cap is a shiny alloy cover glued over a Stant cap; once you know how the new cap mechanism works you understand the old one.

I prised out the metal retaining ring from the old cap and the old mechanism came out easily, as explained above, don't damage the old black Stant cover glued into the shiny lotus cap.

My lock was still securely clipped into the old black cover, it is not easy to remove so I kept the old lock and its keys.

A smear of thick silicone grease on the ratchet pawls might make it last a bit longer. Check the cap and lock works as it should and if all is OK, push the new retaining ring into place.

Took 1/2 an hour to disassemble the new cap, and 10 mins to transfer the mechanism to the new one.

An alternative method to disassemble the new cap is to use a diamond cutting disk in a Dremel to cut around the black plastic outer cap(do this about 3mm from the top of the cap), and then make a couple of vertical cuts down to the bottom of the cap. Be aware that the plastic is only about 1.5mm thick, so these cuts must not run too deep. I kept to the safe side and cut 1mm deep and then used a small screw driver to lever the cap apart. This took about 2 minutes.